Electrical Installation

Vacuum Air Circuit Breakers in MV Distribution System for Electrical Construction

Vacuum Interrupter of a Vacuum Air Circuit Breakers

The air vacuum circuit breakers are of the triple pole indoor type for rated voltage 24 KV. They operate on the vacuum arc quenching principle and outstandingly cost effective. The vacuum breaker consists of the mechanism 2 housing complete with stored energy mechanism and control elements. The three poles with vacuum interrupters, cast resin insulators and bracing struts, and the operating rods connecting the mechanism with the breaker poles.

Lighting Fixtures In Building Projects

The scope of this specification covers the supply and installation of lighting fixtures applicable to internal and external places of a building. Work includes, the collection, handling, installation and commissioning of the fluorescent, incandescent, chandelier, mercury vapour lamp light fixtures.

Telephone System In Electrical Construction Works

The contractor shall furnish and install a telephone system as specified herein and as shown in the drawings.

APPLICABLE PUBLICATIONS FOR TELEPHONE SYSTEM

The following publications of the issues listed below, but referred to thereafter by basic designation only, form a part of this specification to the extend indicated by the reference thereto:

Method Statement For The Installation Of Power and Lighting System Wiring

Electrical Power and Lighting System Wiring

1. Introduction and Scope

This method of statement specifies the detailed requirements and procedures for the installation of Power and Lighting System Wiring.

2. Applicable Project Specification

Section: Cables and wiring

Division: Installation

Sub Division: Subdivision

Method Statement For Installation Of Galvanized Conduits On Exposed Surface

Method Statement For Installation Of Galvanized Conduits that has to be installed on the Exposed Surface of a building is described here.

1. Introduction and Scope

This method of statement specify the detailed requirements and procedures for the installation of Galvanized Conduits for the exposed surface installation requirement for MEP services of the above building.

Method Statement For Installation of Electrical DB, SMDB and MDB Panelboards

Electrical Panel Boards - DB, SMDB and MDB

1. Introduction and Scope

This method statement is written for the purpose of establishing method and procedures for the Installation of DB, SMDB and MDB Panelboards.

2. Applicable Projects Specification

Section: SWITCHBOARD DISTRIBUTION PANELS AND MCCs.
Division: INSTALLATION
Sub Division: Subdivision

3. Location of Activity

Low Voltage Room and Electrical Rooms

Method Statement For Installation Of Cable Tray Or Trunking

Ladder type Cable Tray Installation Method

Electrical Engineers seldom show interest acquiring knowledge and experience on cable tray installations. Most of them think it's a concern of mechanical fabricators to be taken care of it. A proper and professional way of cable tray installation requires good involvement and coordination of people from both electrical and mechanical disciplines. If cable tray system has been installed appropriately in a project, following advantages can be counted:

Cable Tray system enhances safety of electrical wiring system.
Cable tray installation provides dependability in any circumstances.
Cable Tray system saves space, materials, labor, time and cost.
Maintenance and extension of cable tray installation are easier than any other wiring system.

Hence, electrical installation of a project must give high priority to adopt properly evaluated cable tray wiring system if aesthetic impact is low. This article explains how to make a typical method statement for cable tray or trunking installation for a building project.

Electrical Engineering

Electrical engineering deals with practical applications involving current flow through conductors; focuses on the design, construction, and operation of electrical systems and equipment. It includes developing, producing and testing of electrical and electronic devices and equipment, such as, generators to produce and distribute electricity, electric motors and other electrical machinery, transmission line.

Medium Voltage Cables (MV Cables) In Electrical Construction

The contractor shall supply, install, test and commission the 13.8 KV cable network as shown and indicated on the contract documents. Conductor sizes shall be metric as shown, conductor sizes with cross sectional areas smaller than specified will not be accepted. The cable installation shall include all trench work, sleeves, ducts, and all necessary fixings and cable terminations at both ends of the cable. The contractor shall supply and install cable marker posts to indicate the route of all underground cables. Markers shall be provided at every bend along the route and at sites of crossing roads or pipe lines.

Emergency Power Diesel Generating Set In Electrical Construction

This article covers the manufacture, supply, installation, testing and commissioning of 415 volts, 3 ph, 4 wire, Diesel Alternator Set (Diesel Genset). The set shall be mounted on common base frame and complete in all respects including the auxiliary equipment such as battery auxiliary, lube oil pumps, filters, oil storage tank, centrifuge, etc. including piping required for interconnection between the set and the auxiliaries which are mounted separately.